When using a mobile rack and your hard drive contains a Windows XP OS, you can follow these instructions so you will not encounter any error moving on another machine.
From Micro$oft support ...
I will repost the contents of the URL here in case they remove it from that URL.
This article helped a lot of analysts that I know....
=======================================================
Microsoft support article
You receive a Stop 0x0000007B error after you move the Windows XP system disk to another computer
SUMMARY
This article describes how you may receive a Stop error when you try to start the Microsoft Windows XP-based backup computer after you move the system disk to a backup computer. This issue occurs when registry entries and the drivers for the mass storage controller are not installed in Windows XP. To resolve this issue, use the same hardware in the backup computer.
SYMPTOMS
After you move the Microsoft Windows XP system (boot) disk to a backup computer, you may receive the following Stop error when you try to start the Windows XP-based backup computer:
STOP: 0x0000007B (0xF741B84C,0xC0000034,0x00000000,0x00000000)
INACCESSIBLE_BOOT_DEVICE
INACCESSIBLE_BOOT_DEVICE
CAUSE
This error may occur if the registry entries and the drivers for the mass storage controller hardware in the backup computer are not installed in Windows XP.
For integrated device electronics (IDE) controllers, there are several different chip sets available, such as Intel, VIA, and Promise. Each chip set has a different Plug-n-Play identifier (PnP-ID).
The PnP-ID information of mass storage controllers for the backup computer must be in the registry before startup so that Windows XP can initialize the correct drivers.
For integrated device electronics (IDE) controllers, there are several different chip sets available, such as Intel, VIA, and Promise. Each chip set has a different Plug-n-Play identifier (PnP-ID).
The PnP-ID information of mass storage controllers for the backup computer must be in the registry before startup so that Windows XP can initialize the correct drivers.
RESOLUTION
To resolve this error, use the same hardware for the backup computer:
For SCSI-based system disks, you can prime the registry and make sure that the drivers that you want are in place by installing the SCSI controller that is used by the backup computer before you transfer the system disk contents. Windows XP PnP detects the controller, sets up critical registry entries, and copies the appropriate driver.
After you see the SCSI controller in Device Manager, you can remove the alternate controller. If you have to move the system disk to another computer that has the same make and model of SCSI controller in the future, Windows XP will start successfully because Windows XP has already used that controller one time and has retained the correct configuration information.
| • | Replace the problem hardware components in the backup computer with components of the same manufacturer, make, and model as the motherboard in the computer that you are backing up. |
| • | If the system disk is a SCSI disk, use the same make and model of SCSI controller in the new computer. |
| • | If the system disk is an IDE disk, use the same kind of motherboard in the new computer, a motherboard that has the same kind of IDE chip set and the same PnP-ID as the motherboard in the computer that you are backing up. |
After you see the SCSI controller in Device Manager, you can remove the alternate controller. If you have to move the system disk to another computer that has the same make and model of SCSI controller in the future, Windows XP will start successfully because Windows XP has already used that controller one time and has retained the correct configuration information.
MORE INFORMATION
Although Microsoft does not support this method, you can import or merge the required registry entries, and copy the drivers beforehand to support all IDE controllers that are natively supported by Windows XP. Note that although this method might enable the relocated system disk to start successfully, other hardware differences can lead to other problems.This solution provides support for IDE controllers whose PnP-ID matches one of the PnP-IDs in the following list. However, if you want to determine beforehand the IDE controllers that are used in your current and backup computers, you can search the %SystemRoot%\Setupapi.log file for the PnP-ID that is detected while the Setup program is running.
After you determine the PnP-IDs that are used in your computers, you can choose to merge or to populate the registry with only the PnP-IDs that you need.
The following list shows the PnP-IDs of natively supported IDE controllers in Windows XP:
;*********** Standard IDE ATA/ATAPI Controllers *********To import this information, follow these steps on two different test computers that exhibit the Stop 0x0000007B error after you change disks between computers. After you follow this procedure on each test computer, you can probably move the hard disks and start both computers without receiving the Stop 0x0000007B error. However, other hardware differences can cause other problems.
Secondary_IDE_Channel=%SystemRoot%\inf\Mshdc.inf
;*********** Generic ESDI Hard Disk_Controller **********
*PNP0600=%SystemRoot%\inf\Mshdc.inf
;*********** Aztech IDE Controller **********************
*AZT0502=%SystemRoot%\inf\Mshdc.inf
;*********** Device ID for Generic Dual PCI IDE *********
PCI\CC_0101=%SystemRoot%\inf\Mshdc.inf
;************ALI IDE Controller ******************************
PCI\VEN_10B9&DEV_5215=%SystemRoot%\inf\Mshdc.inf
PCI\VEN_10B9&DEV_5219=%SystemRoot%\inf\Mshdc.inf
PCI\VEN_10B9&DEV_5229=%SystemRoot%\inf\Mshdc.inf
;************Appian Technology **************************
PCI\VEN_1097&DEV_0038=%SystemRoot%\inf\Mshdc.inf
;************CMD Technology *****************************
PCI\VEN_1095&DEV_0640=%SystemRoot%\inf\Mshdc.inf
PCI\VEN_1095&DEV_0646=%SystemRoot%\inf\Mshdc.inf
PCI\VEN_1095&DEV_0646&REV_05=%SystemRoot%\inf\Mshdc.inf
PCI\VEN_1095&DEV_0646&REV_07=%SystemRoot%\inf\Mshdc.inf
PCI\VEN_1095&DEV_0648=%SystemRoot%\inf\Mshdc.inf
PCI\VEN_1095&DEV_0649=%SystemRoot%\inf\Mshdc.inf
;************Compaq *************************************
PCI\VEN_0E11&DEV_AE33=%SystemRoot%\inf\Mshdc.inf
;*************Intel *************************************
PCI\VEN_8086&DEV_1222=%SystemRoot%\inf\Mshdc.inf
PCI\VEN_8086&DEV_1230=%SystemRoot%\inf\Mshdc.inf
PCI\VEN_8086&DEV_7010=%SystemRoot%\inf\Mshdc.inf
PCI\VEN_8086&DEV_7111=%SystemRoot%\inf\Mshdc.inf
PCI\VEN_8086&DEV_2411=%SystemRoot%\inf\Mshdc.inf
PCI\VEN_8086&DEV_2421=%SystemRoot%\inf\Mshdc.inf
PCI\VEN_8086&DEV_7199=%SystemRoot%\inf\Mshdc.inf
PCI\VEN_8086&DEV_244A=%SystemRoot%\inf\Mshdc.inf
PCI\VEN_8086&DEV_244B=%SystemRoot%\inf\Mshdc.inf
PCI\VEN_8086&DEV_248A=%SystemRoot%\inf\Mshdc.inf
PCI\VEN_8086&DEV_7199=%SystemRoot%\inf\Mshdc.inf
PCI\VEN_8086&DEV_7601=%SystemRoot%\inf\Mshdc.inf
;*************PC Technology *****************************
PCI\VEN_1042&DEV_1000=%systemroot%\inf\Mshdc.inf
;*************Silicon Integrated System *****************
PCI\VEN_1039&DEV_0601=%SystemRoot%\inf\Mshdc.inf
PCI\VEN_1039&DEV_5513=%SystemRoot%\inf\Mshdc.inf
;*************Symphony Labs *****************************
PCI\VEN_10AD&DEV_0001=%SystemRoot%\inf\Mshdc.inf
PCI\VEN_10AD&DEV_0150=%SystemRoot%\inf\Mshdc.inf
;*************Promise Technology ************************
PCI\VEN_105A&DEV_4D33=%SystemRoot%\inf\mshdc.inf
;*************VIA Technologies, Inc. ********************
PCI\VEN_1106&DEV_0571=%SystemRoot%\inf\Mshdc.inf
;*************Standard Microsystems Corp. ***************
PCI\VEN_1055&DEV_9130=%SystemRoot%\inf\Mshdc.inf
;*************Toshiba ***********************************
PCI\VEN_1179&DEV_0105=%SystemRoot%\inf\Mshdc.inf
| 1. | Copy the following information into Notepad, and then save the file on a 3.5-inch disk. Name the file Mergeide.reg, without the .txt file name extension. ********** Start copy here ********** Windows Registry Editor Version 5.00********** End copy here ********** |
| 2. | Extract the Atapi.sys, Intelide.sys, Pciide.sys, and Pciidex.sys files from the %SystemRoot%\Driver Cache\I386\Driver.cab file, or copy the files to the %SystemRoot%\System32\Drivers folder. |
| 3. | In Microsoft Windows Explorer, right-click the Mergeide.reg file in the floppy drive, and then click Merge. Windows XP displays the following message: Click Yes. After the import process is completed, Windows XP displays another message: |
| 4. | Quit Windows XP, turn off the computer, and then move the system disk to the other test computer, the one that previously produced a Stop 0x0000007B error, and then test to see if you can successfully start the second computer. ======================================================= |
1 comment:
Nice post Zarestel!
Maybe it would be better to read the core of this post at the Microsoft KB page. In this way one gets the latest/complete version:
as the last bits
http://support.microsoft.com/kb/314082
I noticed the last bits of that page at MS indicates this applies to both Win XP home and to Win XP Professional. The "Applies To" and "Keywords" (kbregistry kberrmsg kb3rdparty kbenv kbprb KB314082) was omitted in your original post.
Post a Comment